How to Install Disaster Relief Tent

 A disaster relief tent is mainly used for field research, camping, exploration, construction, disaster relief, flood control and long/short term living in the field.

How to set up a disaster relief tent is something that many users often ask after purchasing a tent, we have simple installation instructions here, you can refer to them.

 

The tent is a rectangular double-slope straight wall construction style. The entrance door is on one side of the wall, with a triangular window at the top; the other side of the wall has a square window and a triangular window at the top; the two sides of the wall have two square windows each, with a removable screen enclosure. The whole tent is fixed with triangular stakes by pulling the rope.

 

I. Introduction of disaster relief tent

a) The tent is in the form of a double-slope upright wall. The frame is a plug-in structure, with a floor crossbar. It can be used safely under the self-weight and 8-level wind.

b) As shown in the picture, the 12m² disaster relief tent is 3.7m long, 3.2m wide, 2.67m high at the top, and 1.75m high at the eaves.

c) Assembly time: 15min/6 people.

d) It can be used continuously for more than 2 years under normal conditions.

 

Ⅱ. Building process

a) Open the packing bag, take out the canopy and frame and other parts separately, and count the number of each part according to the product packing list.

(According to the number on the drawing to splice, from top to bottom installation, a little while to complete. Note that the splices should be aligned, first, splice a place and then splice a place, do not do it at the same time, if you do it at the same time may lead to a waste of time because of uncoordinated cooperation.)

b) Take 8 general-purpose rods and three groups of end frame tee and middle frame tee that have been pressed together to fix the wire rope, forming three groups of connected herringbone frame and connecting.

c) Take 4 general-purpose rods and end frame tee and middle frame tee to form a frame.

d) Place the canopy on the three groups of herringbone frames and adjust the position.

e) Take 6 upright rods and insert them into the end frame tee and center frame tee, and use 6 people to support the canopy at the same time, and connect them with the placed ground rods.

f) Tie all parts of the tent tightly, fasten the nylon zipper, and adjust the position of the tent to connect with each pole of the frame.

g) Drive triangle stakes in the corresponding position on the ground, fix the drawstring, adjust the tightness, and put the rubber stakes headset on the end of the triangle stakes.

h) Tidy up the tent and bury it with soil along the tent perimeter.

 

Ⅲ. Withdrawing

a) Tent withdrawal process and erection of the opposite, withdrawal with reference to the erection of the method, the reverse order of steps can be.

b) When folding the tent body, according to the size of the integrated packaging bag tent body part (1830mm×150mm×150mm) iterate well, and then put into the integrated packaging bag tent body part.

c) After the tent poles and parts are counted according to the product packing list, put them into the fixed frame and put them into the frame part of the integrated packaging bag.

 

Ⅳ. Maintenance precautions

a) When erecting and withdrawing, do not drag the tent body on the ground to avoid soiling and tearing, causing unnecessary damage.

b) In the process of use, pay attention to keeping the inside and outside of the tarp clean.

c) After the rain, snow, and high wind, check the roof and the surrounding ground for water, snow and loose rope, etc., clean up and adjust in time to ensure that the tent is in a normal state of use.

d) The disaster relief tent after dampness is not allowed to be stored for a long time, must be dried in time, and then packaged for storage.

e) Tent parts shall not be moved to other uses.

f) The tent bag should be properly stored with the tent, not lost, in order to be recycled.

g) Tent in the process of use, such as found in the parts should be damaged in time to replace.